Navigator NV223 Ohaus

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Sample preparation stirrer Modernize your laboratory with Guardian 5000 Series shakers, designed to  (more)be safe and deliver exceptional safety and superior performance. Numerous cutting-edge Ohaus features: - SafetyHeat system to protect the laboratory: an industry-leading sensing system uses two independent safety controls to continuously monitor the electronics and shut off the heat before it overheats - Powerful and consistent shaking performance: precise stirring from 60 to 1600 rpm is made possible by the design of a powerful, robust motor with magnet and software controlled ramp rate, ensuring safe stirring even for viscous applications. - Easy to read LCD display with everything you need to know: the bright LCD display includes temperature and speed settings, intuitive icons and hot top indicator - Durable and reliable with SmartHousing: smartHousing is resistant to chemicals with an innovative and easy to clean design; the lines allow any liquid spills to drain out of the instrument Available models: Model e-G51HP07C: plate 178x178mm; flow rate 15 litres; ceramic plate; heating up to 500°C. Model e-G51HS07C: plate 178 x 178mm; flow rate 15 litres; ceramic plate; heating up to 500°C and stirring up to 1600rpm. Model e-G51HS10C: plate 254x254mm; flow rate 18 litres; ceramic plate; heating up to 500°C and stirring up to 1600rpm. Model e-G51HSRDM: plate Ø135mm; flow rate 18 litres; aluminum plate; heating up to 380°C and stirring up to 1600rpm. Model e-G51ST07C: plate 178x178mm; flow rate 15 litres; ceramic plate; stirring up to 1600rpm. Applications Boiling water, water/oil bath preparation, sample and solution preparation, dissolution buffers and reagents, sample concentration Display Backlit LCD display for temperature and speed, green lights when unit is heating and agitating, prominent hot light, probe in use icon, single point calibration icon Operation Stirring from 60 to 1600 rpm, ambient temperature range from +5°C to 500°C (ceramic top) or 380°C (aluminum top), power cord (included), the stirring models include a 1.5” (3.8cm) PTFE coated stir bar Construction Probe connection, SmartHousing™ stays cool to the touch and is resistant to chemicals, IP21 rated, polycarbonate front panel, control knobs, On/Off switch to disconnect heater, integrated pole holder, easy-to-use ceramic or aluminum tops to clean Characteristics Hot top light, audible alarm, SafetyHeat™ protection shuts down heater in case of malfunction, temperature calibration function for 3 probes and 3 platen setpoints

DIONEX ICS 2000 Ion Chromatography System RFIC + ASE 200 Lab Tabletop Accelerated Solvent Extractor  (more)for parts 2 Modules dionex for parts only

Heating thermostat from 20 to 200°C, with LCD display and simple programming functions LAUDA ECO sta (more)nds out for its range of features and ease of use. ECO thermostats are available in Silver (LCD display; simple programming) and Gold (TFT color display; complex programming) models, equipped with a mini USB interface as standard. A LAUDA innovation is the pressure flow controller located on the front of the head. This means that flow regulation between inside and outside is possible even during operation. - Monochrome LCD graphic display for simultaneous indication of actual and set values - The circulation pump can be adjusted to six levels - Integrated programmer: 1 program with max. 20 segments - Fully electronic continuous regulator with PID action - Additional key Tmax for overtemperature protection - The ECO heating thermostat line includes transparent baths up to 100°C and stainless steel up to 200°C - The most powerful units are equipped with the energy-saving LAUDA SmartCool system - Variants in 230V; the 50 Hz are also available with natural refrigerants - Convenient operation with softkey cursor - Safety class III for operation with flammable and non-flammable liquids. - mini-USB interface - Pump connections with 13mm plastic nipples as standard LAUDA tank thermostats are equipped as standard with a cooling coil. The E 4 model is also equipped with a lid for the bowl and connections for external applications. A drain cock on the rear side makes changing the heat transfer liquid easy and safe. Grafico delle prestazioni di riscaldamento dei termostati di immersione ECO Silver con vasca in acciaio inox. Performance graph of the pump pressing on the six levels. TECHNICAL VISUALIZATION Display 1 - Status display 2 - Display of the internal or external temperature value (T-int or T-ext) 3 - Soft-key bar Control panel 4 - Soft keys, left and right 5 - Enter key 6 - Cursor keys for Up, Down, Left and Right. 7 - T max key: display and adjustment of the overtemperature switch-off point 1 - USB interface 2 - Upper module receptacle approx. 51 mm x 27 mm for analog, RS 232/485 module, Profibus module and contact module 3 - Lower module receptacle approx. 51 mm x 17 mm for Pt100/LiBus module 4 - Connection socket 75S for control cable of cooling underpart for RE 1050 S 5 - Rating label 6 - Connection socket 51H for power supply between the control head and cooling underpart 7 - Mains connecting lead 1 - Cooling coil connections 2 - Pump connection: outflow and return (as standard only with E 4 S and ET 15 S) 3 - Four feet 1 - Mains connecting lead 2 - Rating label 3 - Bath draining tap 4 - Bath drain point

Vigorous agitation The powerful rod stirrers are able to process even the most demanding substances, (more) ensuring a smooth start and vigorous stirring at maximum speed! Velp's LS can reach speeds of 2000 rpm, making it ideal for volumes up to 25 liters and medium viscosities, with a maximum of 25,000 mPa*s. Convenient chuck and high security The intuitive spindle locking system is the simplest and most comfortable available on the market, and does not require any special tools, offering the possibility of using different rod models, for the most varied applications, with a maximum diameter of 10 mm. VELP Scientifica solutions are extremely intuitive and easy to use, being equipped with the most advanced features in terms of safety, including overload and overtemperature. All models operate according to IP 40. Longest possible longevity All our solutions have been carefully designed to offer a long life to the instrument, even in the most difficult operating conditions. The structure covers and protects the engine from any aggressive liquids and vapours, preventing internal corrosion phenomena. The robust motor guarantees continuous operation over the years, without additional costs for maintenance. Resistant structure in technopolymer The special technopolymer structure of the VELP Scientifica rod stirrers guarantees excellent chemical resistance, without equal, and particular handling, being among the lightest on the market. Simple to install, resistant and intuitive, they offer a small footprint, to make the most of the space on the counter. DLH rod stirrer video: Available models: The stirring rods available: For added versatility, you can choose between different types of control, digital or analog. - Digital: set speed, actual speed, torque and timer at a glance. - Analog: power and precision at the most advantageous price. Simple keys, graphics and intuitive design; you'll already know how to use it the first time you turn it on. Peace of mind and safety in your laboratory with every Velp instrument. - Protection in case of overload and overheating - Intuitive temple closing system, without the use of special tools. Maximum rod diameter of 10 mm Compact and lightweight, small in size to make the most of your laboratory bench space. - Technopolymer structure - IP40 protection

MULTI-HS 15 DIGITAL VELP MAGNETIC STIRRER SAFETY AND RESISTANCE - Warning message on the display whe (more)n the plate reaches 50°C - The Safety Lock function prevents unintentional changes of settings in order to meet all laboratory safety standards. - The VELP CerAlTop ™ top plate is made of aluminum alloy which guarantees temperature homogeneity with excellent heat distribution and high specific power thanks to the circular configuration. A thin layer of ceramic protects the plate from scratches and chemicals and guarantees high resistance to thermal stress and thermal shock. SMART AND SIMPLE USER INTERFACE The LED display is easy to read and thanks to the intuitive icons the operator will always have an eye on the working conditions: - Active heat - Temperature set point - Activating the timer - Automatic reverse option - Lock button Two extremely precise rotary knobs control the temperature and speed setting and to start the heating you need to press the knob; a small detail that exemplifies Velp's utmost attention to operator safety. By touching both knobs simultaneously, it is possible to access the advanced menu for the most suitable configuration of all operating modes. POWER AND PRECISION - The extremely powerful Brushless motors are able to stir from 100 up to 1000 rpm, offering practically unlimited duration over time. The stirring speed is always constant, even when the viscosity changes, thanks to the SpeedServo ™ torque compensation. - The middle button allows you to set the timer for unsupervised work. The Timer can be set from 1 min up to 99 hours and more advanced configurations can be set in the advanced menu. - The Auto-reverse option improves the kinetics by changing the direction of the stirring direction. You can also set the direction change to your preferred time interval. TECHNICAL FEATURES: Stirring position distance: 74 mm. Stirring speed: 100 - 1000 rpm. Speed setting accuracy: 5 rpm. Temperature setting resolution: 1°C. Hot top warning: on display (>50°C). Timer: from 1 min to 99 h: 59 min. Timer setting steps: 1 min. Autoreverse: from 5 s to 99 min-59 s. Autoreverse setting steps: 1 s.

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

REFRIGERATED LABORATORY INCUBATORS ST SMART POL-EKO ST - STABILITY AND QUALITY AT THE BEST PRICE Bei (more)ng able to both heat and cool, ST incubators are perfect for the stable and safe incubation of samples, in any working environment. The ST series maintains a constant temperature from 3°C to 40°C with excellent precision. As an option, the range can be extended up to +70 °C. Operation at ambient temperature +10°C...+28°C, for cooled incubators with glass door +10°C...+25°C. It's necessary to purchase automatic defrosting function (ST/CHL PLUS) for all units operating at set point <=5°C to prevent icing. Large touch display, LED lighting, alarms, lock, simple and comfortable design, will make using these incubators a breeze; and thanks to the programming with time and temperature profiles, you will be able to carry out highly precise and repeatable incubations. But it doesn't end here, continue reading and discover all the other surprising features of these incubators! WHICH VERSION? THE THREE VERSIONS OF THE ST MODEL The three models differ in the materials of the internal chamber, the materials of the shelves and the safety class. This subdivision allows you to choose based on your real needs, meeting your budget. BASIC: aluminum interior; metal grid shelves; safety class 1.0 (DIN 12880). COMFORT: stainless steel interior according to DIN 1.4016; stainless steel grill shelves; safety class 1.0. PREMIUM: Interior in acid-resistant stainless steel according to DIN 1.4301; stainless steel grill shelves; safety class 2.0. As an option, at the bottom of the page, you can find the ST-INOX accessory; this allows you to order your ST refrigerated incubator with polished stainless steel exteriors, rather than powder-coated sheet metal (light gray with graphite front panel) as standard. ABSOLUTE CONTROL CONTROL PANELS The SMART control panel is among the most complete you can find on the market. Large symbols and temperature values ​​guarantee comfortable and clear reading, combined with disarming ease of use. The latest generation touch screen responds to commands even if touched with latex gloves and is equipped with a large display: all values ​​are perfectly readable from any angle, regardless of the intensity of the light. More and more? POL-EKO has already thought about it. For those who want cutting-edge functions and the freedom of transfer and remote use, POL-EKO offers you the SMART PRO controller. You can find all the differences between the SMART and SMART PRO panel in our dedicated post: insights on SMART and SMART PRO. With the SMART PRO versions, more accessories and options will also be available. DO YOU KNOW THE ADVANTAGES OF AN ADVANCED CONTROLLER LIKE THE SMART PANEL? - Sharp 4.3' color touch screen - Quick and easy data transfer: via LAN or USB - Fast, multi-segment, time and temperature programming - Visual and audible alarms with colored bar on display - Internal memory for programs and data storage - User manual downloadable directly from the controller - Loop function up to 255 times or infinite - Controls can be managed even when wearing latex gloves - Recording of the minimum, average and maximum temperature value for each segment - Overview of the set and current parameters during operation - Operation in temperature or time priority mode - ... and much more QUALITY FIRST Resistant. Durable. POL-EKO incubators are designed and built to guarantee the best performance. They are a smart purchase, for customers who want to invest in the future of their laboratory. By choosing these products you will have precise results for years and years, repeatable and in complete comfort. The ST SMART series incubators are built with the best materials and equipped with the most important accessories, to give you a complete and ready-to-use standard product. - Insulated door with lock - Internal LED light - Optional internal and/or external glass door - USB port for downloading recording data, events, manuals, service. - LAN port - Open door alarm - Access port for external sensor on the side - Quality control protocol (in +37°C) - Available with FOT: phytoperiodic system – day and night simulation. To find out more, download our informative PDF: The photoperiodic (FOT) and phytotron (FIT) systems by POL-EKO. The three versions of the ST models The three models differ in the materials of the internal chamber, the materials of the shelves and the safety class. This subdivision allows you to choose based on your real needs, meeting your budget. BASIC: aluminum interior; wire shelves; over temperature protection class 1.0. COMFORT: stainless steel interior according to DIN 1.4016; stainless steel wire shelves; over temperature protection class 1.0. PREMIUM: Interior in acid-resistant stainless steel according to DIN 1.4301; stainless steel wire shelves; over temperature protection class 2.0. As an option, at the bottom of the page, you can find the ST-INOX accessory; this allows you to order your ST refrigerated incubator with polished stainless steel exteriors, rather than powder-coated sheet metal (light gray with graphite front panel) as standard. ST SMART SERIES POL-EKO offers 10 models of refrigerated incubators with capacities from 70 to 1540 litres. The ST series also offers multi-chamber models with two or three separate and independently controlled internal compartments. These solutions allow you to save space in the laboratory and perform tests at different temperatures. Mixed multichambers are also available, such as incubator-refrigerator or incubator-freezer combinations. DETAILS AND ACCESSORIES Every detail of your POL-EKO models is designed to make routine work as simple and comfortable as possible. Below, the front and rear view. 1 - rating plate 2 - Temperature sensor 3 - Shelf 4 - Access port for external sensor 5 - Adjustable feet 6 - Solid external door 7 - Ventilation 8 - Lock 9 - Touch screen control panel 10 - USB port 11 - Door open sensor 1 - Main switch 2 - Condenser 3 - Cooling system 4 - Fuse 5 - Main power socket 6 - LAN port For larger models: a - Anchor rods b - Integrated power cable c - Fuse d - Main switch e - LAN port OPTIONS POL-EKO allows you to increase the possibilities of your incubator with quality accessories; to better adapt to particular applications or to equip the instrument with safety systems and advanced connections. In the photo, the beautiful glass doors supplied with the ST models. - Internal glass door - External glass door - Grid shelf - Stainless steel grill shelf - Perforated shelf - Reinforced shelf - Stainless steel basins - Aluminum or stainless steel drawer with guides - Wheels - Coffee table with wheels - Automatic defrost function - Heating up to 70°C - Photoperiodic system - POT - Internal socket - LabDesk software - IQ OQ PQ calibration and qualification - Overtemperature protection class 3.3 according to DIN 12880 - Backup battery for the display in case of power failure - Dry alarm contact - LAN cable - Non-standard 20/60/100 mm access door - Additional 30 mm access door